IBM 2night: December 2016

Saturday, 31 December 2016

JN0-643 Enterprise Routing and Switching, Professional (JNCIP-ENT)

JNCIP-ENT Exam Objectives (Exam: JN0-643 and JN0-646)

OSPF
Describe the concepts, operation and functionality of OSPFv2 and OSPFv3
OSPF LSA types
OSPF area types and operations
LSA flooding through an OSPF multi-area network
DR/BDR operation
SPF algorithm
Metrics, including external metric types
Authentication options
Route summarization and restriction
Overload
Virtual links
OSPFv2 vs OSPFv3
Given a scenario, demonstrate knowledge of how to configure and monitor single-area and multi-area OSPF
Implement OSPF routing policy

BGP
Describe the concepts, operation and functionality of BGP
BGP route selection process
Next hop resolution
BGP attributes - concept and operation
BGP communities
Regular expressions
Load balancing - multipath, multihop, forwarding table
NLRI families - inet, inet6
Advanced BGP options
Given a scenario, demonstrate knowledge of how to configure and monitor BGP
Implement BGP routing policy

IP Multicast
Describe the concepts, operation and functionality of IP multicast
Components of IP multicast, including multicast addressing
IP multicast traffic flow
Any-Source Multicast (ASM) vs. Source-Specific Multicast (SSM)
RPF - concept and operation
IGMP, IGMP snooping
PIM dense-mode and sparse-mode
Rendezvous point (RP) - concept, operation, discovery, election
SSM - requirements, benefits, address ranges
Anycast RP
MSDP
Routing policy and scoping
Given a scenario, demonstrate knowledge of how to configure and monitor IGMP, PIM-DM and PIM-SM (including SSM)
Implement IP multicast routing policy

Ethernet Switching and Spanning Tree
Describe the concepts, operation and functionality of advanced Ethernet switching
Filter-based VLANs
Private VLANs
Dynamic VLAN registration using MVRP
Tunnel Layer 2 traffic through Ethernet networks
Layer 2 tunneling using Q-in-Q and L2PT
Given a scenario, demonstrate knowledge of how to configure and monitor advanced Ethernet switching
Filter-based VLANs
Private VLANs
Dynamic VLAN registration using MVRP
Tunnel Layer 2 traffic through Ethernet networks
Layer 2 tunneling using Q-in-Q and L2PT
Describe the concepts, operation and functionality of advanced spanning tree protocols, including MSTP and VSTP
Given a scenario, demonstrate knowledge of how to configure and monitor MSTP and VSTP

Layer 2 Authentication and Access Control
Describe the operation of various Layer 2 authentication and access control features
Authentication process flow
802.1x - concepts and functionality
MAC RADIUS
Captive portal
Server fail fallback
Guest VLAN
Considerations when using multiple authentication/access control methods
Given a scenario, demonstration how to configure and monitor Layer 2 authentication and access control

IP Telephony Features
Describe the concepts, operation and functionality of features that facilitate IP telephony deployments
Power over Ethernet (PoE)
LLDP and LLDP-MED
Voice VLAN
Given a scenario, demonstrated how to configure and monitor features used to support IP Telephony

Class of Service (CoS)
Describe the concepts, operation and functionality of Junos CoS for Layer 2/3 networks
CoS processing on Junos devices
CoS header fields
Forwarding classes
Classification
Packet loss priority
Policers
Schedulers
Drop profiles
Shaping
Rewrite rules
Given a scenario, demonstrate knowledge of how to configure and monitor CoS for Layer 2/3 networks

QUESTION 1
Which connection method do OSPF routers use to communicate with each other?

A. IP protocol number 89
B. TCP port 179
C. UDP port 179
D. IP protocol number 6

Answer: A

Explanation:

QUESTION 2
Which statement is true about default BGP route redistribution behavior?

A. IBGP-learned routes are advertised only to other IBGP peers.
B. EBGP-learned routes are redistributed into any IGPs.
C. EBGP-learned routes are advertised only to other EBGP peers.
D. EBGP-learned routes are advertised to other IBGP and EBGP peers.

Answer: D

Explanation:

QUESTION 3
In a PIM-SM network, which type of node helps to build a tree towards an unknown multicast
source?

A. DIS
B. RP
C. DR
D. BSR

Answer: B

Explanation:

QUESTION 4
Which statement is true about MVRP?

A. It allows you to split a broadcast domain into multiple isolated broadcast subdomains.
B. It dynamically manages VLAN registration in a LAN.
C. It maps multiple independent spanning-tree instances onto one physical topology.
D. It is a Layer 2 protocol that facilitates network and neighbor discovery.

Answer: A

Explanation:

QUESTION 5
Which statement is true about LLDP?

A. It allows you to split a broadcast domain into multiple isolated broadcast subdomains.
B. It dynamically manages VLAN registration in a LAN.
C. It maintains a separate spanning-tree instance for each VLAN.
D. It is a Layer 2 protocol that facilitates network and neighbor discovery.

Answer: D

Explanation:

Click here to view complete Q&A of JN0-643 exam
Certkingdom Review

Best Juniper JN0-643 Certification, Juniper JN0-643 Training at certkingdom.com

Tuesday, 27 December 2016

JN0-532 FWV, Specialist (JNCIS -FWV)

JNCIS-FWV Exam Objectives (Exam: JN0-532)

VPNs
Identify IKE Phase 1/Phase2 negotiation sequence and proposals
Identify/differentiate IPSec standard elements (encapsulations, SA, SPI, etc.)
List steps for policy-based/route-based VPN configuration
Relate proxy-ID to VPN setup
Identify proper configuration for various hub/spoke configurations (policy, int. placement, etc.)
Identify NHTB requirements/configurations
Configure/verify AC-VPNs
Identify PKI components (certificates, CDL, etc.)
List steps for PKI implementation w/ VPNs
VPN Variations
Configure Dynamic Peer VPNs
Configure Transparent mode VPNs
Configure Overlapping Networks
Describe GRE applications/Configure GRE

Network Management
Configure local management (SSL, SSH, management restrictions).
Interpret internal counters and logs.
Configure SYSLOG.
Discuss logging levels.
Configure SNMP.

Troubleshooting with Debug/Snoop
Enable debug/snoop.
Set debug filters.
Set snoop filters.
Use get commands to validates/troubleshoot routing and policies.
Use debug output to identify routing and policy problems.
Use get commands to validate/troubleshoot address translation.
Use debug output to identify problems.
Use get commands to validate/troubleshoot VPN setup.

Traffic Management
Describe the bandwidth allocation process.
Describe queuing functionality.
List requirements/steps for configuring traffic management.

Virtual Systems
Define VSYS applications
Describe root vs. VSYS administration
Explain VSYS vs. root assignment of routes/NAT pools/etc.
Configure interface-based VSYS
Configure inter-VSYS communications, including NAT.
Use show/debug output to identify VSYS usage.
Configure VSYS resource allocation

NSRP
Distinguish active/passive and active/active.
Describe NSRP operations (HA link, session sync, master election, etc.)
Configure active/passive and active/active NSRP.
Validate NSRP operations.
Adjust operations (secondary link, failover settings).
Configure redundant interface.

Dynamic Routing/Routing over VPNs
Configure RIP over VPNs
Configure OSPF over VPNs
Configure/verify OSPF routing
Configure OSPF options
Configure/verify BGP
Configure redistribution/filters/route maps
Configure static routes incl. floating static routes
Configure/verify source routing
Configure/verify policy routing

Attack Prevention
Describe SCREEN functions
Describe/configure Deep Inspection
Describe/configure anti-virus functionality
Configure web filtering

Multicast
Configure/verify IGMP
Configure/verify PIM-SM

QUESTION 1
You have created a VPN to a dynamic peer. Which two configured parameters must match?
(Choose two.)

A. static side peer-id
B. dynamic side local-id
C. static side IP address
D. dynamic side IP address

Answer: A,B

QUESTION 2
Which three events would cause ScreenOS devices to generate SNMP traps? (Choose three.)

A. cold starts
B. traffic alarms
C. warm reboots
D. self log events
E. traffic log events

Answer: A,B,C

QUESTION 3
Which command shows the filter applied to snoop captures?

A. get snoop
B. snoop info
C. get ffilter
D. get ffilter ip-proto snoop

Answer: B

Click here to view complete Q&A of JN0-532 exam
Certkingdom Review

Best Juniper JN0-532 Certification, Juniper JN0-532 Training at certkingdom.com

JN0-532 FWV, Specialist (JNCIS -FWV)

QUESTION 3
Which command shows the filter applied to snoop captures?

A. get snoop
B. snoop info
C. get ffilter
D. get ffilter ip-proto snoop

Answer: B

Click here to view complete Q&A of JN0-532 exam
Certkingdom Review

Best Juniper JN0-532 Certification, Juniper JN0-532 Training at certkingdom.com

Friday, 23 December 2016

JN0-661 Service Provider Routing and Switching JNCIP-SP

JNCIP-SP Exam Objectives (Exam: JN0-661)

OSPF
Describe the concepts, operation and functionality of OSPFv2 or OSPFv3
OSPF area types and operations
LSA flooding through an OSPF multi-area network
DR/BDR operation
SPF algorithm
Metrics, including external metric types
Summarize and restrict routes
Virtual links
OSPFv2 vs OSPFv3
Given a scenario, demonstrate knowledge of how to configure or monitor single-area and multi-area OSPF
Implement OSPF routing policy

IS-IS
Describe the concepts, operation, or functionality of IS-IS
IS-IS areas/levels and operations
LSP flooding through an IS-IS multi-area network
DIS operation
SPF algorithm
Metrics, including wide metrics
Route summarization and route leaking
Given a scenario, demonstrate knowledge of how to configure or monitor single-area and multi-area IS-IS
Implement IS-IS routing policy

BGP
Describe the concepts, operation, or functionality of BGP
BGP route selection process
Next hop resolution
BGP attributes – concept and operation
BGP communities
Regular expressions
Multipath
Multihop
Load balancing
Advanced BGP options
BGP route damping
Multiprotocol BGP
Describe the concepts, operation or functionality of BGP scaling mechanisms
Route reflection
Confederations
Given a scenario, demonstrate knowledge of how to configure or monitor BGP
Implement BGP routing policy

Class of Service (CoS)
Describe the concepts, operation, or functionality of Junos CoS
CoS processing on Junos devices
CoS header fields
Forwarding classes
Classification
Packet loss priority
Policers, including tricolor marking and hierarchical policers
Schedulers
Drop profiles
Shaping
Rewrite rules
Hierarchical scheduling (H-CoS) characteristics (high-level only)
Given a scenario, demonstrate knowledge of how to configure or monitor CoS

IP Multicast
Describe the concepts, operation, or functionality of IP multicast
Components of IP multicast, including multicast addressing
IP multicast traffic flow
Any-Source Multicast (ASM) versus Source-Specific Multicast (SSM)
RPF – concept and operation
IGMP
PIM dense-mode and sparse-mode
Rendezvous point (RP) – concept, operation, discovery, election
SSM – requirements, benefits, address ranges
MSDP, including single and multi-PIM domains
Anycast RP
Routing policy and scoping
Given a scenario, demonstrate knowledge of how to configure or monitor IGMP, PIM-DM, PIM-SM (including SSM) and MSDP
Implement IP multicast routing policy

Advanced MPLS
Describe the concepts, operation, or functionality of MPLS
Routing table integration options for traffic engineering
Routing policy to control path selection
Advanced MPLS features
Administrative groups
Advanced CSPF options
Implement MPLS routing policy

Layer 3 VPNs
Describe the concepts, operation, or functionality of Layer 3 VPNs
Traffic flow – control and data planes
Full mesh vs. hub-and-spoke topology
VPN-IPv4 addressing
Route distinguishers
Route targets
Route distribution
Site of origin
Sham links
vrf-table-label
Layer 3 VPN scaling
IPv6 Layer 3 VPNs
Layer 3 VPN Internet access options
Given a scenario, demonstrate knowledge of how to configure or monitor the components of Layer 3 VPNs
Describe the concepts, operation or functionality of multicast VPNs
Next-generation MVPNs (NG-MVPN)
Flow of control and data traffic in an MVPN
Describe Junos support for carrier-of-carriers or interprovider VPN models

Layer 2 VPNs
Describe the concepts, operation, or functionality of BGP Layer 2 VPNs
Traffic flow – control and data planes
Forwarding tables
Connection mapping
Layer 2 VPN NLRI
Route distinguishers
Route targets
Layer 2 VPN scaling
Describe the concepts, operation, or functionality of LDP Layer 2 circuits
Traffic flow – control and data planes
Virtual circuit label
Layer 2 interworking
Describe the concepts, operation, or functionality of VPLS
Traffic flow – control and data planes
BGP VPLS label distribution
LDP VPLS label distribution
Route targets
VPLS Multihoming
Site IDs
Describe the concepts, operation, or functionality of EVPN
Traffic flow – control and data planes
MAC learning and distribution
EVPN Multihoming
BGP EVPN label distribution
Given a scenario, demonstrate knowledge of how to configure or monitor Layer 2 VPNs
BGP Layer 2 VPNs
LDP Layer 2 circuits
EVPNs
VPLS

QUESTION 1
Which OSPFv3 router ID is valid?

A. 192.168.1.1
B. ::192.168.1.1
C. 0.0.0.0
D. 2008:db8::1

Answer: A

Explanation

OSPFv3 Router IDs, Area IDs, and LSA link-state IDs remain at the OSPFv2 IPv4 size of 32 bits.
References: Network Configuration Example OSPF Version 3 for IPv6 Feature Guide, page 3

QUESTION 2
You are working with a new MPLS network that is using the default EXP classifier and default schedules.
A small amount of traffic is being placed in the assured
forwarding class. No other traffic is passing through the network at this time.
In this scenario, what happens to the traffic that is being placed in the assured forwarding class?

A. The traffic is reclassified to the best effort forwarding class and is forwarded.
B. The traffic remains in the assured forwarding class and is forwarded.
C. The traffic is reclassified to the network control forwarding class and is forwarded.
D. The traffic remains in the assured forwarding class and is dropped.

Answer: B

Explanation

References: https://www.juniper.net/documentation/en_US/junos15.1/topics/concept/forwarding-classes-default-cos-config-guide.html

QUESTION 3
You are connecting your OSPF router to your customer's RIP router and redistributing
the customer's routes into your OSPF domain. Your OSPF routes is part of an NSSA
and the ABR is injecting an OSPF default route, which you have advertised to your customer.
After committing the configuration, you notice a routing loop
between your OSPF router and the customer's RIP router.
Which action must you perform on your OSPF router to solve this problem?

A. Enable Type 7-to-Type 5 LSA conversion.
B. Set the customer-facing interface to passive.
C. Convert the area to a stub area.
D. Change the OSPF external route preference.

Answer: D

Explanation

Avoid routing loops by changing the OSPF external route preference.

Incorrect Answers:
A: If multiple NSSA ABR routers are present, it is recommended that not all ABRs perform
Type 7-to-5 translation to avoid routing loops.
B: We would have to make the interface on the RIP router, the customer router,
passive, not the customer-facing interface on the OSPF router.

Note: By default RIP broadcasts are sent from all interfaces. RIP allows us to control this behavior.
We can configure which interface should send RIP broadcast or
which not. Once we mark any interface as passive interface, RIP will stop sending updates from that interface.

References: https://www.juniper.net/documentation/en_US/junos15.1/topics/topic-map/ospf-stub-and-not-so-stubby-areas.html

QUESTION 4
A PE provides VLAN VPLS service to a CE attached with two links.
You want to prevent Layer 2 loops and provide link redundancy.
Which two actions will accomplish this task? (Choose two.)

A. Place both interfaces in a link aggregation group.
B. Configure different VLANs on each interface.
C. Configure all VLANs on both interfaces, on the PE, and on the CE.
D. Configure Spanning Tree Protocol between the PE and the CE.

Answer: B,D

Explanation

D: To prevent the formation of Layer 2 loops between the CE devices and the multihomed PE routers,
Juniper recommends that you employ the Spanning Tree
Protocol (STP) on your CE devices. Layer 2 loops can form due to inconfiguration.
Temporary Layer 2 loops can also form during convergence after a change in the network topology.

References: http://www.juniper.net/documentation/en_US/junos16.1/topics/topic-map/vpls-bgp-multihoming.html

Click here to view complete Q&A of JN0-661 exam
Certkingdom Review

Best Juniper JN0-661 Certification, Juniper JN0-661 Training at certkingdom.com

Thursday, 22 December 2016

JNCDS-SEC Exam Objectives (Exam: JN0-1330)

JNCDS-SEC Exam Objectives (Exam: JN0-1330)

Fundamental Security Concepts
Describe the various tenets of common security features
Access control lists
Stateful security policies
ALG’s
IPS
UTM
NAT
IPsec
Next-generation firewall
Screen

Advanced Security Concepts
Describe advanced security features
Security intelligence
Advanced anti-malware
Defense in-depth

Securing the Campus and Branch
Describe the security design considerations within a campus or branch network
Network segmentation
Network access
Wireless
802.1X
Remote access VPN’s
NAT
End-to-end security
BYOD

Securing the Enterprise WAN
Describe the security design considerations for an enterprise WAN
Internet edge security design principles
WAN aggregation
Private WAN
VPNs

Securing the Service Provider WAN
Describe the security design considerations for a service provider WAN
DoS/DDos attacks
Securing the control plane
Internet security
CG-NAT

Securing the Data Center
Describe the security design considerations in a data center
Securing data center interconnects
Securing North-South flows
Securing East-West flows
Virtual routers

Security Automation and Management
Describe the design considerations for security management
Securing the individual devices
Centralized security
Junos Space management platform
Junos Space Security Director and Log Director
Juniper Secure Analytics

Security Virtualization
Describe the security design considerations for a virtualized environment
NFV
Service chaining
Micro-segmentation
vSRX

High Availability
Describe the design considerations of high availability in a secure networks
Physical high availability
Virtual high availability
Asymmetrical traffic handling
Chassis clustering

QUESTION: No: 1
You are asked to implement port-based authentication on your access switches. Security and ease of
access are the two primary requirements. Which authentication solution satisfies these requirements?

A. MAC RADIUS
B. network access control
C. firewall authentication
D. IPsec tunnel

Answer: A

QUESTION: No: 2
What is one way to increase the security ofa site-to-site IPsec VPN tunnel?

A. Implement a stronger Diffie-Hellman group.
B. Change IKE Phase 1 from main mode to aggressive mode.
C. Implement traffic selectors.
D. Implement a policy-based VPN.

Answer: C

QUESTION: No: 3
Your customer is planning the deployment of a new hub-and-spoke WAN architecture that must support
dual stack They have decided against using a dynamic routing protocol. They are concerned about the
difficulty of managing configurations and operations at the hub location as they deploy branch routers
In this scenario, what ate three reasons for selecting route-based VPNs with traffic selectors'? (Choose
three)

A. Traffic selectors support IPv4 and IPv6.
B. Traffic selectors reduce the number of Phase 2 IPsec security associations.
C. Traffic selectors reduce latency because they bypass UTIVI.
D. Traffic selectors support auto route insertion
E. You can define mutliple traffic selectors within a single route-based VPN

Answer: A,D,E

Click here to view complete Q&A of JN0-1330 exam
Certkingdom Review

Best Juniper JN0-1330 Certification, Juniper JN0-1330 Training at certkingdom.com

Tuesday, 20 December 2016

JN0-943 Enterprise Routing and Switching, Expert

JN0-943 Enterprise Routing and Switching, Expert

At the pinnacle of the Enterprise Routing and Switching certification track is the 1-day JNCIE-ENT practical exam. This exam is designed to validate the networking professionals’ ability to deploy, configure, manage and troubleshoot Junos-based enterprise routing and switching platforms. Throughout this 8-hour practical exam, candidates will build an enterprise network infrastructure consisting of multiple routers and switching devices. Successful candidates will perform system configuration on all devices, configure protocols and features like IPV6, OSPF V2, OSPF V3, BGP, MSDP, PIM, SSM, RSTP, LLDP, 802.1x, CoS, routing policies.

The JNCIE-ENT is valid for two years. Re-certification is achieved by passing the current version of the JNCIP-ENT exam.

Exam topics may include:
System Services and Security
Interfaces
Ethernet Switching
IGPs
BGP
Protocol-Independent Routing
Multicast
Class of Service

System Services and Security
System Services
NTP
Syslog
sFlow
Authentication and authorization
Configuring archival
RPM
PoE
Securing the Control Plane
Stateless firewall configuration

Interfaces
Implementation of Interfaces
Aggregated Ethernet
VRRP
Ethernet OAM
GRE tunnels
BFD
Logical tunnel interfaces

Ethernet Switching
Spanning Tree Protocol
Multiple CIST
MSTP/VSTP/RSTP
xSTP interoperability
Multiple topologies
Optimization
VLANs
VLAN switching and trunking
Q-in-Q
IP Telephony
Private VLANs
Voice VLANs
Virtual Chassis
Master determination
Add/remove members
VCP and VCEP interfaces
Split detection
Security features
Port security features
Dynamic ARP inspection with DHCP snooping
Layer 2 firewall filters
MAC table filtering

IGPs
OSPF
Multi-area OSPF topologies
Filter and summarize routes
Network and link types
Route selection process
BFD
Redistribution
IPv6

BGP
Implementation and Troubleshooting
Routing policy
Route selection
2-byte and 4-byte AS
Multi-homed stub-AS
BFD

Protocol-Independent Routing
Load Balancing
Hash key
Per flow
Filter-based Forwarding
Based on Layer 4
Based on IFL
Configuring Routes
Aggregate
Static
Generated
Policies

Multicast
Implementation of Multicast
Shared tree and source tree
Designated router
RPF table manipulation
SSM
Extend the group range
SSM mapping
RP Redundancy
Anycast RP (PIM and MSDP)
BSR

Class of Service
Implementation
Loss priority
Rewrite rules
Shaping and policing
Scheduling
BA and MF classification
Drop profiles

Click here to view complete Q&A of JN0-943 exam
Certkingdom Review

Best Juniper JN0-943 Certification, Juniper JN0-943 Training at certkingdom.com

Saturday, 3 December 2016

JN0-314 Junos Pulse Access Control, Specialist (JNCIS-AC)

JNCIS-AC Exam Objectives (Exam: JN0-314)

Overview
Identify the concepts, operation, and functionality of Junos Pulse Access Control Service
Junos Pulse Access Control Service components
Component functions and interaction
Identify the components of the access management framework
Interrelationship between realms, roles and policies

Platform Configuration
Demonstrate knowledge how to configure the basic elements of a Junos Pulse Access Control Service environment
Initial Junos Pulse Access Control Service configuration
Choosing the platform (e.g., virtual or physical)
Configure authentication servers
Connectivity verification

Roles
Identify the concepts, operation and functionality of roles
Purpose of roles
Role mapping
Customization of the end-user experience
Demonstrate knowledge of how to configure roles
Roles and role options

End User Access
Identify the Junos Pulse Access Control Service client access options
Junos Pulse
Odyssey Access Client (OAC)
Machine authentication and third party supplicant
Agentless access
Demonstrate knowledge of how to configure Junos Pulse Access Control Service clients
Junos Pulse
Odyssey Access Client (OAC)
Agentless access

Firewall Enforcement
Identify the concepts, operation and functionality of firewall enforcement
Purpose of resource policies
Resource policies for firewall enforcement
User-based firewall policies
Captive portal
Demonstrate knowledge of how to configure firewall enforcement
Junos Pulse Access Control Service configuration
SRX Series device configuration
User-based firewall policies
Captive portal

Layer 2 Enforcement
Identify the concepts, operation and functionality of Layer 2 enforcement techniques
802.1X security
RADIUS (related to 802.1X)
MAC authentication
Multiple supplicant authentication on EX Series devices
Demonstrate knowledge of how to configure Layer 2 enforcement
Junos Pulse Access Control Service configuration
EX Series device configuration
SRX Series device configuration

Endpoint Defense
Identify the concepts, operation and functionality of endpoint defense
Host Checker
Authentication policies and role restrictions
Demonstrate knowledge of how to configure endpoint defense
Host Checker
Authentication policies and role restrictions

Authentication Options
Identify the concepts, operation and functionality of user authentication
Authentication process
Authentication options
Demonstrate knowledge of how to configure authentication
Authentication servers including LDAP, RADIUS, AD/NT, anonymous
Authentication realms

Management and Troubleshooting
Demonstrate knowledge of how to manage and troubleshoot a Junos Pulse Access Control Service environment, including Junos Pulse Access Control Service and SRX Series devices
Logging (e.g., RADIUS logging, policy tracing)
System Monitoring
File Management
Information collection
Component connectivity
End user connectivity and enforcement

High Availability
Identify the concepts and requirements for high availability in a Junos Pulse Access Control Service environment
Clustering
Deployment options and considerations
Demonstrate knowledge of how to configure high availability
Junos Pulse Access Control Service configuration
SRX Series device configuration

Integration
Identify the concepts and requirements for Junos Pulse Access Control Service integration with other components
Integration with IF-MAP client
Integration with STRM
Integration with SRX Series devices
Integration with EX Series devices
Demonstrate knowledge of how to configure integration
IF-MAP federation
Syslog

QUESTION 1
A customer wants to create a custom Junos Pulse configuration. Which two are required?
(Choose two)

A. Connection set
B. Configuration set
C. Custom installer
D. Component set

Answer: A,D

Explanation:

QUESTION 2
What is a type of firewall enforcer supported by the Junos Pulse Access Control Service?

A. Checkpoint firewall
B. SRX Series device
C. DP sensor
D. MX Series device

Answer: B

Explanation:

QUESTION 3
A customer is trying to decide which 802.1X inner protocol to use on their network. The customer
requires that no passwords be sent across the network in plain text, that the protocol be supported
by the Windows native supplicant, and that the protocol supports password changes at Layer 2.
Which protocol would meet the customer's needs?

A. EAP-TLS
B. EAP-MD5
C. PAP
D. EAP-MSCHAPv2

Answer: D

Explanation:

QUESTION 4
You navigate to "UAC" > "Infranet Enforcer" > "Auth Table Mapping" in the admin GUI. You see
one policy, which is the unmodified, original default policy.
Which statement is true?

A. Dynamic auth table mapping is not enabled.
B. A successful authentication attempt will result in a new authentication table entry, which will be
delivered only to the Junos enforcer protecting the network from which the user has authenticated.
C. To create a static auth table mapping, you must delete the default policy.
D. The default policy applies only to the factory-default role User.

Answer: A

Explanation:

QUESTION 5
You have a Junos Pulse Secure Access Service acting as an IF-MAP client, configured to federate
all user roles to a Junos Pulse Access Control Service acting as an IF-MAP Federation server. A
remote user using Junos Pulse logs in to the Junos Pulse Secure Access Service; the Junos
Pulse Secure Access Service provisions a remote access session for that user.
What happens next?

A. The Junos Pulse Secure Access Service redirects the user to the Junos Pulse Secure Access
Service for authentication
B. The Junos Pulse Access Control Service provisions enforcement points to enable resource
access for that user.
C. The Junos Pulse Secure Access Service publishes user session and role information to the IFMAP
Federation server,
D. The Junos Pulse Secure Access Service provisions enforcement points to enable resource
access for that user.

Answer: C

Explanation:

Click here to view complete Q&A of JN0-314 exam
Certkingdom Review

Best Cisco JN0-314 Certification, Cisco JN0-314 Training at certkingdom.com